Russian original raid backpack 60+ SPLAV

Primary section:

• Backpack rear due to the multi-layer structure has high rigidity and provides excellent ventilation. Inside vertical pockets for removable armor. The back has the correct anatomical shape
• The front area of the backpack is trimmed with PALS slings for hanging additional pouches (6 cells in width, 7 horizontal rows of lines in height)
• Tube with two cord tighteners and two compression straps on top
• The lower entrance ("basement") with a zipper and two phalages. Inside the backpack there is a septum in the form of a tube with a cord draw
• On the sides of the backpack sash vertical 20 mm fibecs and large tractor zippers for quick installation / removal of removable pockets
• Side pockets-pads with a rubberized top and an eyelet for draining the water
• Side screeds on the fibstacks that can be stretched both on top of the removable pockets and under them, for which under the tractor pockets of the pockets there are special slots in which the screeds are threaded
• 3 carrying handles - on top of backrest, on top and bottom of front face
• Strengthened bottom
• The kit includes a protective cape, located in a separate pocket of the valve
• At the bottom of the backpack stitches for attaching additional cargo

Straps:

• Removable, height-adjustable straps. Large width, anatomical silhouette. Two layers of foam and an Airmesh mesh for softness and ventilation. The top pullers. Cells PALS for fastening pouches are made by laser cutting in reinforced fabric, which provides straps with a thin profile and a flat surface, without interfering with the application of weapons
• Removable chest screed
• On the sides of the backpack sash vertical 20 mm fasteners and large tractor zippers for quick installation / removal of removable pockets. Fasteners are installed on the top strings of the straps
• Non-standard bottom fastening straps for the possibility of carrying removable pockets as a small knapsack. By the end of each strap is sewn a long sling and a three-slot buckle. To the lower corners of the backpack and removable pockets are sewn half rings. The sling is threaded into a half ring on a backpack or a removable pocket and then back to a three-slot buckle on the straps

Belt:

• Removable wide belt - an analogue of the belt RPM / rucksack. Lateral pullers, PALS cells along the entire length (including the posnitsu), 4 semi-rings for hanging the straps of the RPS (compatibility with webbing lightweight shoulder straps v.3)
• Fastened to the backpack by passing under the lumbar cushion, inside the belt is fastened with velcro

Valve:

• Removable height-adjustable valve
• On the front of the valve is a Velcro for chevrons, a removable logo in the kit
• Volumetric pocket
• Flat pocket with removable protective cape (included)
• Stitches for additional cargo

Removable pockets:

• Included
• Pockets are the same and interchangeable
• Fastened with a zipper, entrance from above
• On the back of the pocket on top there is a rubberized slot for the withdrawal of the drinking system tube (not included in the kit!). Inside the sewn suspension of the drinking system from the slings with velcro
• On the front surface of the sewing lines are vertical slings for fixing the additional load, also underneath are the side ties of the backpack (if they go over the removable pockets)
• Above and at the bottom of the sewing lines for securing additional cargo
• On the back of each pocket, fastening sashes for various carrying options - vertical tractor zippers, two adjustable 20 mm fasteners from the top and two semicircles from the bottom:

Fastening to the sides of the backpack: pull the adjustment of the pockets of the pockets to a minimum, fasten them to the reciprocal backbones on the sides of the rucksack, fasten the reciprocal tractor zippers
Fixing pockets to chest straps: use the supplied lines with tri-slit buckles (2 pcs.) To connect the half rings at the ends of the backpack belt with one half-ring on each pocket, pull the adjustment of the lines to the required length. Fasten the pockets of the pockets to the reciprocal fastenings of the chest fasteners on each shoulder, adjust the required length so that the pocket is well fixed in the figure
Fastening one pocket to the straps (a small knapsack): remove the straps from the backpack. Fasten the pockets of the pockets to the two nearest closest straps to the center, adjust the necessary length of the straps. Pass the straps of the straps into the half rings at the bottom corners of the pocket, then into the three-slit buckles of the straps, adjust the required length of the straps
Fastening of two pockets to straps (small knapsack): detach straps from backpack. Fasten two pockets together with the help of side tractor lightning. Fasten the phastes of each pocket to the response straps of the straps on the corresponding shoulder, adjust the necessary length of the lines. Pass the straps of the straps into the two extreme half rings of the bottom corners of the pockets, then into the three-slit buckles of the straps, adjust the required length of the straps

Volume of the maximum: 75 l

Backpack volume (with valve): 60 l

The volume of removable pockets: 7.5 liters + 7.5 liters

Maximum weight: 3.2 kg

Weight without side pockets: 2.8 kg

Weight of pockets: 0,2 + 0,2 kg

Main compartment (W × H × T): 35 × 50 × 25 cm

Side pocket (2 pcs.) (W × H × T): 16 × 36 × 13 cm

Pocket on the valve (W × H × T): 35 × 10 × 25 cm

Lower pocket (W × H × T): 35 × 10 × 25 cm

Main fabric: Polyester 600D

Plastic fittings: Duraflex®